Universal Aiming Device
Part No. 50000
A high quality, adjustable aiming
device for pre-drilling and pin placement. While commonly used for coxofemoral
luxation repair with the toggle pin method,
this instrument can also be used for many other applications including: lag
screw repair of condylar fractures, placement of calcaneo-tibial screws for
repair of Achilles tendons, and lag screw fixation of femoral neck fractures.
A variety of screw-in-place drill guides are available to support many drill
bit diameters. One single hole drill guide of your choice is included with
the
purchase of the IMEX™ Universal Aiming Device.
Drill Guides for Universal Aiming Device
Screw-in-place drill guides can be
easily interchanged, and seven drill guide
diameters are available. All drill guides can be purchased independently
as needed.
| Part No. |
Drill Diameter |
| 50016 | 1.6mm |
| 50020 | 2.0mm |
| 50023 | 2.3mm |
| 50025 | 2.5mm |
| 50031 | 3.1mm |
| 50035 | 3.5mm |
| 50039 | 3.9mm |
| 50045 | 4.5mm |
| 50016D | 1.6mm x 2 holes |
Toggle Pins
Three diameters are available for repair of coxofemoral luxations.
The cross hole sizes are compatible with most commonly used sizes of monofilament
suture
material. Depending on the size of suture used, the required drill bit may
be approximately the same size as the toggle pin or up to 1-2
millimeters larger (to allow for large suture.) The blunt end of a suture
passer can be used to assist with final passage of the toggle pin through
the acetabular wall. Implant quality 316LVM stainless steel.
| Part No. | Diameter | Length | Cross Hole |
| 55027 | 2.7mm | 10mm | 1.1mm |
| 55032 | 3.2mm | 14mm | 1.1mm |
| 55040 | 4.0mm | 18mm | 1.9mm |
Polypropylene
Suture Buttons
Part No. 55100
These two-hole suture buttons are used at the lateral femur to
simplify suture tie-off when performing the toggle pin method of coxofemoral
reduction.
Approximately 6.5mm x 14mm. 2.0mm hole diameters can accommodate
virtually all large suture materials. Check for availability of pre-sterilized
version - Part No. 55100S.
Suture Passer
Part No. 55000
Similar to a large sewing needle with an eye, this suture passer
is designed to be a very economical method of pulling suture down the femoral
neck. The
passer diameter is 3.2mm. With suture included, it is often necessary
to utilize a 3.5mm or larger pilot hole. This instrument is most useful when
utilizing soft-pliable suture material, while hard nylon leader is usually
pushed through the femoral hole by hand. The blunt end is also utilized to “pop” the
toggle pin through the acetabular component.
Hip Luxation Starter Kit
Part No. 55SKT
| Quantity | Part No. | Description |
| 1 | 50000 | Universal Aiming Device, Complete |
| 1 | 50035 | Universal Aiming Device Drill Guide 3.5mm |
| 1 | 55000 | Suture Passer 3.2mm |
| 3 | 55100S | Polypropylene Suture Buttons |
| 1 | 32035 | StickTite™ Drill Bit 3.5mm |
| 1 | 32039 | StickTite™ Drill Bit 3.9mm |
| 6 | 55032 | Toggle Pins 3.2mm |
